homesystemsweekly.focalledger.comPeriod 2026-11-20

Entry · Ref 9ZYXCQ9C

What to Check Before Winter for a Reliable Heating System

Posted
2026-11-19
Last amended
2026-11-19
Account
@homesystemsweekly

When the temperature drops and the snow starts to fall, a dependable heating system is not just a matter of comfort - it is a necessity. For homeowners in Brant County and nearby Ontario communities, making sure the heating system works properly before the deep cold arrives can save a lot of trouble, expense, and worry. A few simple checks, done ahead of time, can catch small problems before they become big ones. This article walks through the main points to look at, from the thermostat to the chimney, so that the system runs smoothly all season long.

Start with the Thermostat

The thermostat is the brain of the heating system. It tells the furnace when to turn on and off, based on the temperature setting. If the thermostat is not working correctly, the furnace may cycle on and off too often, run longer than needed, or not come on at all. Check that the thermostat is set to "heat" mode and that the temperature setting is a few degrees above the current room temperature. If the system does not respond, try replacing the batteries. Many modern thermostats use batteries for the display and wireless functions, and weak batteries can cause erratic behaviour. Also, make sure the thermostat is not located near a drafty window, a heat source like a lamp or a television, or in a spot that gets direct sunlight. Any of these can fool the thermostat into reading the wrong temperature, making the furnace run when it should not or stay off when it should run.

Inspect the Air Filter

A clean air filter is vital for good airflow and efficient operation. The air filter traps dust, pet hair, and other particles from the air before it passes through the furnace. Over time, the filter becomes clogged, which reduces airflow. When airflow is restricted, the furnace has to work harder to push air through the system. This extra strain can lead to higher energy use and can cause the heat exchanger to overheat. A dirty filter is one of the most common causes of furnace breakdowns. Check the filter at the start of the heating season and then monthly during heavy use. If the filter is disposable, replace it with a new one of the same size and type. If it is washable, clean it with water and let it dry completely before putting it back. A clean filter helps the system run more quietly and keeps the blower motor from having to work too hard.

Check the Venting and Airflow

The furnace needs to breathe. It takes in air for combustion and then vents the exhaust gases outside. If the vents are blocked by debris, leaves, snow, or animal nests, the system cannot work properly. Blocked combustion air intakes can cause incomplete burning, which can produce carbon monoxide - a colourless, odourless gas that is dangerous at high levels. Blocked exhaust vents can cause the furnace to shut down on a safety limit or, worse, push exhaust gases back into the house. Walk around the outside of the house and look at the vent pipes. They are usually metal or plastic pipes that come out of the wall or roof near the furnace. Clear away any leaves, twigs, grass clippings, or snow. Also check the indoor vent pipes for any signs of rust, cracks, or loose joints. If the venting system uses a chimney, look up the chimney with a flashlight to see if it is clear. A bird nest or a buildup of soot can restrict the flow. Any signs of blockage or damage mean the system should be checked by a qualified technician before the furnace is used.

Look at the Burner Assembly and Heat Exchanger

The burner assembly is where the fuel - usually natural gas or propane - mixes with air and burns to create heat. The heat exchanger then transfers that heat to the air that circulates through the house. Over time, soot and dirt can build up on the burner and the heat exchanger surfaces. This buildup reduces the efficiency of the heat transfer and can cause uneven heating. In a gas furnace, a dirty burner can also lead to a yellow or flickering flame, which is a sign that the fuel is not burning completely. A complete inspection of the burner assembly and heat exchanger requires the furnace to be opened and the components to be cleaned with special tools. This is not a job for a homeowner. The safety controls, gas pressure, and electrical connections all need to be checked by a professional. That is where furnace inspections by a qualified technician come in. A technician can remove the burner, clean it, inspect the heat exchanger for cracks or corrosion, and make sure the flame is burning clean and blue. They can also check the gas pressure and the safety limit switches. Having this done once a year, before the heating season starts, is the best way to avoid a mid-winter breakdown.

Listen to the Blower Motor

The blower motor pushes the heated air through the ductwork and into the rooms. When the motor starts to fail, it often makes a whining, squealing, or grinding noise. It may also run slowly or not at all. If the motor bearings are worn, the motor can overheat and trip a safety switch, shutting the system down. Before the season starts, turn the furnace on and listen to the blower. A quiet, smooth hum is normal. Any unusual noise is a sign that the motor may need to be oiled or replaced. The motor has oil ports on some models, but newer motors are sealed and cannot be oiled. If the noise is loud or the motor does not start, call a technician. They can measure the motor's amperage and check the capacitor and the fan wheel. A failing blower motor is one of the most common reasons for a no-heat call in the middle of winter, so catching it early is worth the effort.

Test the Carbon Monoxide Detectors

Carbon monoxide is a serious risk with any fuel-burning appliance. The gas is produced when fuel does not burn completely. A well-maintained furnace should produce very little carbon monoxide, but a cracked heat exchanger, a dirty burner, or a blocked vent can cause levels to rise. The best defence is a working carbon monoxide detector on each level of the house, especially near the bedrooms and the furnace room. Test the detectors by pressing the test button. Replace batteries if needed, and replace the detector itself if it is more than seven years old. Many detectors have an end-of-life warning that beeps periodically. Do not ignore that sound. A functioning detector gives peace of mind and can alert the family to a problem before it becomes dangerous. If the detector ever goes off, do not ignore it. Follow the safety steps: turn off the furnace if it is safe to do so, open windows, leave the house, and call the gas company or a qualified technician.

Review the System's Age and Service History

Every heating system has a lifespan. A typical gas furnace lasts between fifteen and twenty years with proper maintenance. As the system ages, parts wear out more often, and efficiency drops. If the furnace is more than fifteen years old and has needed several repairs in the last couple of years, it may be time to start planning for a replacement. An older furnace is also less efficient, which means higher energy bills. The seasonal checklist should include a review of the service records. Look at when the last professional inspection was done and what was found. If there is no record of regular maintenance, it is a good idea to schedule a full inspection before winter. Even if the furnace seems to be running fine, a technician can spot issues that are not obvious to the untrained eye, such as a cracked heat exchanger, a worn blower motor, or a failing igniter. Regular furnace inspections help extend the life of the equipment and keep it running safely and efficiently.

Check the Pilot Light or Ignition System

Older furnaces have a standing pilot light that burns all the time. Newer furnaces use an electronic ignition that lights the burner only when the thermostat calls for heat. If the pilot light is out, the furnace will not run. Check the pilot light window on the furnace cabinet. If the pilot is out, follow the manufacturer's instructions to relight it, but only if you are comfortable doing so. Many modern furnaces have a spark igniter that can be heard clicking when the system starts. If the igniter clicks but the burner does not light, the problem may be a dirty flame sensor or a faulty gas valve. These are jobs for a technician. If the pilot light is yellow or orange instead of blue, that is a sign of incomplete combustion and should be checked by a professional right away.

Inspect the Ductwork and Vents

The ductwork carries the heated air from the furnace to the rooms. Over time, ducts can develop leaks, become crushed, or get blocked by debris. Leaky ducts waste heated air and make the system work harder than necessary. Check the visible ductwork in the basement, attic, and crawl spaces. Look for gaps at the joints, holes, or sections that have come apart. Use metal tape or mastic sealant to seal small gaps. Also check the supply registers in each room. Make sure they are open and not blocked by furniture, rugs, or curtains. A blocked register can cause the furnace to overheat and trip a safety limit. If the furnace is in a room that is sealed off, make sure that room has a return air path so that air can circulate back to the furnace.

Taking the time to go through these checks before the cold weather arrives can make a big difference. A little effort in the fall can prevent a freezing night in January. For the tasks that require tools or expertise, calling in a professional is the right move. A technician's inspection covers everything from the burner assembly to the venting, and they have the equipment to measure gas pressure, check for carbon monoxide leaks, and test the safety controls. With a well-maintained system, the house stays warm, the energy bills stay reasonable, and everyone can sleep well knowing the heat will be there when they need it.

Entry closed✓ Balanced